Ham radio deluxe will not connect to radio serial#On the “Serial Ports” tab of the connect window the virtual serial port presented by SmartSDR CAT is visable. Next let’s start up HRD and setup the CAT connection to the radio. In the DAX Control Panel one final step before moving on, enable “RX Stream 1” by clicking on the “1” which will change the stream to active and the indicator to blue. I have outlined in red below the key configuration areas. In my example below I am running a 5Khz wide slice which while in the example is on a 20 meters PSK frequency, this setup works well across any of the audio based digital modes.įor DAX to work it must be enabled, the slice assigned a DAX channel, it is also a best practice to open up the receiver width to 5k with a corresponding change to the TX High Cut to match. Since we are going through the effort of plumbing up the CAT connection, let us spend a little time setting up the virtual sound card for whatever tickles your fancy. The connection will not actually occur until HRD config is complete. Also shown in the screen capture below, HRD is connected to this port. Below is the end result a Com11 CAT serial port assigned to Slice A. So I thought it a worthwhile use of time to create a similar posting for SmartSDR.Īs the FlexRadio documentation is excellent I will not spend much if any time providing details on how for example to create a port in SmartSDR CAT as the existing user documentation covers this in detail.įirst step is setting up a vitual serial port for HRD to connect to. In the second point: is where my confusion about port selection came from “It doesn’t matter which one you select”.My post covering the setup and use of the Yaesu FTdx3000 with Ham Radio Deluxe (HRD) gets hundreds of hits a week. In first point: I missed the point “Which one you should use depends on where you have connected the serial cable to the radio at the RRC-1258 Radio-RRC” It doesn’t matter which one you select, but you have to select the same in HamRadioDeluxe or other program. Select which Virtual COM-port you want to use in the Local PC. Which one you should use depends on where you have connected the serial cable to the radio at the RRC-1258 Radio-RRC. COM0, COM1 and COM2 is referring to the COM ports of the RRC-1258: Radio-RRC. Select mode for the different RCC Client COM-ports.In the RRC-Micro setup instruction for the COM Port selection, see below: The fact that the SCU-17 communication ports work with both PCC-450 and HAM Radio Deluxe makes me wonder if there is an issue with the RRC-Micro virtual communication ports or is there an issues with how HAM Radio Deluxe connect to and manages the virtual communication port, or I missed something. HAM Radio Deluxe Test 00with RRC-Micro to a RRC-1258MkII with communications parameters of 38400, 8, 2, N. PCC-450 Test 01 with RRC-Micro to a RRC-1258MkII with communications parameters of 38400, 8, 2, N. PCC-450 Test 00with RRC-Micro to a RRC-1258MkII with communications parameters of 38400, 8, 1, N. They have been uploaded to YouTube and the links are below: I recorded video for the three test to show how the system is configured and the results. I have not been able to connect either PCC-450 or HAM Radio Deluxe to the FT-450. I set the communication parameters to match the standard for the Yaesu radio used by HAM Radio Deluxe, 8-bits, 2-stop bits, and no parity at 38400 bps. I mapped the RRC-1258MkII Communication Port 2 to the RRC-Micro Communication Port 0 (COM0) and connected to one of the virtual serial communication port to COM0. When RRC-Micro starts-up the application initializes three virtual serial communication ports which are linked over Ethernet to the RRC-1258MkII. I have both audio and transmit capabilities. When I start up RRC-Micro on my PC, it turns-on the FT-450. I have RRC-Micro setup and connecting to the RRC-1258MkII. Ham radio deluxe will not connect to radio software#The solution I want to implement is based on the RemoteRig hardware and software with HAM Radio Deluxe. To solve this problem I want an independent interface machine that is accessible through the Internet. When I tried to use it over the Internet the audio and transmit voice did not work well. Both Yaesu PCC-450 and HAM Radio Deluxe both have been configured for a serial ports setup as 38400, 8,1, N. My initial setup used an Yaesu SCU-17 interface. I have been working to setup my Yaesu FT-450 for remote control.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |